Garrett G-Series G25-550
Garrett G-Series G25-550
Garrett G-Series G25-550
Garrett G-Series G25-550

Garrett G-Series G25-550

$1,679.67
/
670 Entries 2X
  • In stock, ready to ship
  • Backordered, shipping soon
Size chart
All units are expressed in inches. Measurements are taken by laying garment on a flat surface. Length is measured from the top of the shoulder to the base of the garment. Width is measured from the bottom of one arm hole across the chest to the bottom of other arm hole. Use these measurements to compare to a similar garment in your wardrobe. 
All units are expressed in inches. Measurements are taken by laying garment on a flat surface. Length is measured from the top of the shoulder to the base of the garment. Width is measured from the bottom of one arm hole across the chest to the bottom of other arm hole. Use these measurements to compare to a similar garment in your wardrobe. 

This is listing is for the SUPERCORE ONLY! You will need to purchase your hot-side exhaust housing separately.

Horsepower: 300 - 550

Displacement: 1.4L - 3.0L

FEATURES

  • G SERIES COMPRESSOR AERODYNAMICS FOR MAXIMUM HP
  • 48mm TURBOCHARGER COMPRESSOR WHEEL
  • 80% MAXIMUM COMPRESSOR EFFICIENCY
  • MAR-M ALLOY TURBINE WHEEL RATED UP TO 1050° C
  • NEW TURBINE AERO PROVIDES HIGHER FLOW AND EFFICIENCY
  • TURBOCHARGER ASSEMBLIES ARE CALIBRATED WITH A 0.5 BAR ACTUATOR
  • STAINLESS STEEL TURBINE HOUSINGS RATED UP TO 1050° C
  • OIL RESTRICTOR AND WATER FITTINGS INCLUDED
  • FULLY MACHINED SPEED SENSOR AND PRESSURE PORTS
  • Read About Turbo System Optimization: A guide to setting up your turbocharger
  • The maximum power stated for each turbocharger has been calculated based strictly on choke flow of the compressor map (total turbo capability), which represents the potential flywheel power. Performance results of this product are highly dependent upon your vehicle’s modifications and tuning/calibration. Please consult with your local distributor before making a purchase.

                Turbocharger Part Number Chart:

                G25-550 Reference Data

                 

                SuperCore PN: 858161-5002S

                		 Compressor Turbine
                Inducer Exducer Trim A/R Inducer Exducer Trim
                48mm 60mm 65 0.70 54mm 49mm 84

                 

                G25-550 Standard Rotation Turbine Housing Kits Turbine Kit PN A/R Inlet Outlet Wastegate Divided
                Free float / non-wastegated turbine housing kits are sold

                 

                independently of the supercore

                		 740902-0069 0.72 V-Band V-Band Free Float N
                740902-0068 0.92 V-Band V-band Free Float N
                G25-550 Standard Rotation Turbocharger Assembly Turbo PN A/R Inlet Outlet Wastegate Divided
                Turbo PN is a complete assembly with an internally wastegated

                 

                turbine housing calibrated using a 0.5 bar actuator

                 

                		 877895-5001S 0.49 T25 V-Band Yes N
                877895-5003S 0.72 V-Band V-band Yes N
                877895-5004S 0.92 V-Band V-band Yes N
                877895-5011S 0.92 T4 V-band Yes Y

                THE MOST POWERFUL SMALL FRAME TURBOCHARGER ON THE MARKET

                Introducing performance out of a package you never thought possible. This clean sheet product is tailored to meet the demands of hard core racing enthusiasts while providing industry leading power capability in a small package.

                The G-Series G25-550 and the G25-660 turbochargers are compatible with 1.4L – 3.0L engine displacements and capable of producing up to 550 and 660 horsepower. G Series 25 turbochargers are smaller and outflow all comparable products on the market.

                New compressor and turbine aero combined with high temperature resistant materials allowed engineers to push the limits of performance.

                A new name designates a new generation of industry leading technology and innovation.

                Understanding the Name:
                G25-550 || G25-660

                G designates 81 years of Garrett® heritage.

                25 classifies the size of the frame. The remaining 3 digits identify the max horsepowerrating of the turbocharger. (ie 550)

                COMPRESSOR AERO

                Forged fully-machined compressor wheel and new aerodynamics increase maximum horsepower output and boost response. The CFD (computational fluid dynamics) engineered compressor wheel increases air flow up to 15% for 60mm and 30% for 67mm with 79-80% efficiency. (Compared to GTX GenII)

                Available in standard rotation and reverse rotation options for enthusiasts that want the perfect twin turbo installation or a single reverse rotation turbo for applications with installation restrictions.

                SPEED SENSOR

                The compressor housing features a fully machined ported shroud to help reduce compressor surge. A fully machined speed sensor port provides enthusiasts the option to add the new G Series speed sensor to measure turbocharger shaft speed, a key factor in determining ideal operating conditions.

                The new speed sensor is easy to install and does not need to be adjusted for length like previous sensors. Simply remove and plug, then insert the speed sensor and tighten the bolt. The new speed sensor is sold separately and is not compatible with GT and GTX sensors due to the new design and sizing.
                The addition of an o-ring between the compressor housing and backplate reduces the possibility of boost pressure leakage.

                CENTER HOUSING

                A new one-piece center housing and backplate increase durability and product safety by reducing the number of failure points associated with the turbocharger. The center housing to turbine housing v-band connection allows for 360 degree orientation when installing with Garrett® non-wastegated turbine housings.

                WATER JACKETS

                Four large water jacket ports increase cooling capacity and allow enthusiasts to customize water line routing to help improve the installation process. The turbocharger comes with two -6AN water fittings and two plugs.

                *Recommended to install waterlines on opposite sides of the housing.

                OIL PASSAGE

                A single stage oil passage directs pressurized oil to the new oil cavity ensuring proper bearing lubrication at both sides of the cartridge.

                Each turbocharger includes (1) -4AN oil restrictor fitting with a 1mm orifice to provide the turbo with the recommended 40psi of oil pressure.

                ROTATING GROUP- TWIN PISTON RINGS

                A shorter bearing cartridge allows us to incorporate twin piston rings on both sides of the shaft wheel assembly. This will reduce the likeliness of oil leakage at the seals from the center housing to the compressor and or turbine stage.

                TURBINE WHEEL AERO

                The turbine wheel features all new aerodynamics to improve flow and boost response. The new turbine wheel is made of Mar-M super alloy and is capable of handling exhaust gas temperatures up to 1050 degrees C.
                The new turbine wheel flows 15-20% more than GTX and has peak efficiency of 74%.

                TURBINE HOUSINGS

                All G Series Turbine housings are made from stainless steel to provide ultimate durability and temperature resistance up 1050 degrees C.
                Internally wastegated housings are compact, efficient, and designed with maximum bypass port size to reduce boost creep and provide better boost control.
                Turbine housings are available in a variety of wastegated and non-wastegated, open volute, T25 and Vband configurations so be sure to order the correct part for your application.

                Check These Out!